Call Us: +91 9320899001 / +91 7208014087


Elastomeric Coating provides a long-lastingWaterproof Coating

Exterior masonry walls—particularly ones that are weathered—have long represented one of the most difficult maintenance challenges for the contractor, the painter, and the waterproofer alike.

Most typical exterior surfaces can be successfully protected and maintained by the regular applications of high quality conventional acrylic latex paints. But even the best paints often tend to split and fail when they have been applied over the surface cracks that develop as masonry ages

A Better Alternative: Elastomeric Wall Coatings
The construction chemical industry has known about the limitations of traditional paints on masonry. For almost that long, the industry has been searching for better alternatives. Early attempts to solve the cracking problem, involved formulating coatings with polymers not generally used in conventional paints. Many of these experimental systems provided acceptable service as dirt-resistant coatings.

Unfortunately, virtually all of the polymers tested formed hard films that were too rigid to accommodate the temperature-related fluctuation in the dimensions of the cracks. Inevitably, coatings based on these hard polymers fractured, exposing the masonry to the elements once again.

Recognizing that hard binders were not the answer, the industry turned to "softer'' polymers with much lower glass transition temperatures. Many of the products investigated were already seeing use as binders for caulks and sealants. Because they had low glass transition temperatures, they furnished excellent elasticity and flexibility over a wide range of temperatures.


Instead of depending on a separate, external component to impart flexibility to the film, 100% acrylic elastomeric polymers derive elasticity from a unique combination of special composition, molecular weight, and crosslinking. As a result, they retain flexibility over periods of time. Moreover, formulations based on the 100% acrylic elastomeric polymers exhibit their elastomeric properties over a broad range of temperatures. Thus, the performance of waterborne coatings based on the acrylic elastomerics remains consistently outstanding under all conditions.

In comparing the different types of binders in other areas of performance, the 100% acrylic binders have a significant edge over styrenated products in the area of ultraviolet stabiiity, over viny! acetate products in the area of hydrolysis resistance, and over both chemistries in the area of dirt pick-up resistance. As a result, on extended exposure, waterborne acrylic coatings are more resistant to chalking and do not yellow as do styrenated products. They are not as vulnerable to damage from ambient moisture as acetate-based systems, and they remain cleaner than both types of non-acrylic systems.

Protection with Decoration & Waterproof Elastomeric Exterior Coating

ZC-SEALCOAT is a unique polymer based waterproofing, elastomeric exterior performance coating to protect the concrete structure from degradation in varied climatic conditions. ZC- SEALCOAT is a single component 'Ready to Use' formulation with quick drying properties at room temperature. Its outstanding properties of water repellency coupled with toughness helps to arrest the leakage
during rainy season while its stability against UV radiation keeps the brightness unfazed for years together. Its Two in One performance protects the surface from water seepage & leakage, enhances life of plaster and provides desired aesthetical outlook.

  • Excellent Water Repellency
  • Resistance to U.V. Radiation
  • Resistance to Fungus and moss.
  • No peel-off tendency
  • Tough and Scratch-proof.
  • Excellent Brightness and finish.
  • Stable at high temperatures.
  • Single component, ready to use system
  • Quick drying at room temperature.
  • No water curing required.
  • Can be pigmented in wide colour range
  • CO diffusion resistant
  • Environment friendly
  • Excellent crack bridging
  • Aesthetic Decoration
  • Cost Effective
  • Covering Capacity
  • Surface Preparation :
  • Remove dust, dirt, grease, loose particles, flaking paint, wax, fungus, algae from surface using wire brush. Surface should be washed with water and allowed to dry.
  • Priming :
  • Apply the priming coat using recommended primer or by mixing ZC-SEALCOAT with water in the ratio of 1:2 using brush.
  • Finishing :
  • Finish the surface by applying 2 coats of ZC-SEALCOAT with an intercoat interval of 4 hours.
  • Thinning :
  • ZC-SEALCOAT is ready to apply paint, which does not require thinning.
  • Storage :
  • Keep container closed with a tight lid when not in use. Store in dry place.